Pure Cycles Urban Commuter Assembly

Prep and Tools

• Grease for pedals, stem bolts, and seatpost. i.e. Park Tool Grease
• 4,5,6 wrench or combo folding wrench
• 4,5,6 Torx wrench or combo folding Torx wrench
• 15mm combo wrench
• Favorite beverage (optional but recommended)

The Almighty Unboxing

Make sure your bike is upright with the arrows printed on the box pointed upward.

Cut the binding straps to open the box and lift the bike out by the frame and rear wheel.

Place the bike flat on the ground with the attached front wheel facing upward.

Use scissors to cut the zip ties that secure the front wheel to the frame.

Remove the plastic protectors from the axle and set the wheel aside for the time being.

Next, remove the black protectors from the front and rear dropouts and any other packaging material. (Be careful to stay clear of those cables with your blade).

Leave the bike standing upright and you're ready to move on to the saddle and seatpost!

Seatpost and Saddle Install

Using your 4mm allen key, loosen the seat post collar.

Grease the inside of the seattube of the frame (not the seatpost, unless you want a mess on your hands).

Slide the seat post into the frame ensuring that the minimum insertion marker is below the collar and your saddle is aligned with the frame. (Fine tuning can be done later on).

Then, using your 4mm allen wrench tighten down the seatpost collar.

Alright, let's move on to the bars!

Pedal Install

You'll want to unpack the pedals from the small included cardboard box. The pedals will be marked on their spindles with either an “R” or an “L”. This will indicate which side of bike the pedal will fit. “R” will be for your driveside and “L” will be the opposite. Pedals will often have "L" and "R" stickers too, but they can sometimes fall off in the shuffle, so just remember to check the spindles if you have any doubts.

Make sure that before you install your pedals you properly grease the pedal threads. This will ensure that you are able to remove your pedal down the line if you decide to upgrade.

Apply grease both to the threads on the pedal spindle and in the threads on the crank arm.

Now it's time to bust out that 15mm wrench.  We're going to start on the right-hand side of the bike (driveside). Take the pedal labeled “R” and carefully insert the pedal thread into the right crank arm and begin to turn to the right (clockwise). After the pedal is initially seated, take your 15mm wrench (clockwise still) and get that pedal tightened and secured. Make sure not to over tighten as this can cause stripping.

Now for the left pedal. Take the pedal labeled “L” and, again, begin by greasing the threads on the pedal and the crank arm.

Before we go any further it is vitally important to know that the left pedal is reverse threaded. This means that you're going to tighten the pedal by turning it to the left (counter-clockwise). “Lefty Tighty” might seem a little counterintuitive, but it is massively important to remember when installing your pedals.

Now, carefully insert the pedal thread into the left crank arm and begin to turn to the to the left (counter-clockwise). After the pedal is initially seated, take your 15mm wrench and get that pedal tightened and secured. Again, make sure to not over tighten as this can cause stripping.

After you've finished take a step back and marvel at your work. You're one step closer to having a built up bike! Let's pop that front wheel on there!

Front Wheel Install

Take your front wheel from earlier and grab the quick-release skewer, brake rotor, and rotor bolts from the small "parts" box where you found the pedals.

We'll begin with the brake rotor and the 6 bolts to mount it to the hub. Lay the wheel down, and place the rotor over the hub, aligning the bolt holes.

Take your 3mm Torx wrench and tighten the bolts a bit at a time (just like the stem, so everything stays nice and lined up). Work your way around, doing opposite bolts a bit at a time until the rotor is securely tightened down.

And once the rotor is tightened, find the front brake on the fork and remove the small piece of cardboard that protected the mechanism during shipping.

And now we're ready to get the front wheel mounted! Take the quick-release skewer and remove the end cap and spring from one side (the end cap just twists off, lefty-loosey).

Slide the uncapped end of the skewer through the wheel's hub, and replace the spring and end cap on the opposite side once it's through.

Don't tighten the end cap/skewer all the way, just give it a few twists so everything stays put on both sides.

Now align the front wheel in the dropouts and slide the rotor between the brake pads, the axle into the fork.

Once your wheel is in place, tighten the quick release (hold the end cap and spin the qr lever clockwise). Then "close" the qr lever by pushing it up against the fork. You want it to be fairly hard to push closed, but no so hard that it's impossible. As a rule, it should be pretty tough to get it about 3/4 of the way closed, then it'll make the last quarter easily as it clamps "shut".

 

Making the lever follow the line of the fork is good practice because it makes it easy to "eyeball" that your lever is closed before you roll out and it'll keep it clear from snagging on anything on the road and popping open.

And now your wheel's on there!

If you have excess brake cable, you can snip it to about an inch and re-cap it, or just fold it out of the way and put a kink in the cable so it stays put.

Your brake calipers should be dialed in from the factory, but if you have a rub on one side, pop over here for a quick breakdown on getting everything lined up.

And with the wheel, bars, and saddle on - you're just about all set! Let's do a safety check.